{$cfg_webname}
主页 > 机械机电 > 模具 >

球形端盖造型与模具设计(含cad零件图和装配图)

来源:56doc.com  资料编号:5D10518 资料等级:★★★★★ %E8%B5%84%E6%96%99%E7%BC%96%E5%8F%B7%EF%BC%9A5D10518
资料以网页介绍的为准,下载后不会有水印.资料仅供学习参考之用. 帮助
资料介绍

球形端盖造型与模具设计(含cad零件图和装配图)(含任务书,开题报告,中期检查表,论文说明书11000字,CAD图纸9张)
摘要
我所学习的专业是模具设计与制造专业,这次的毕业设计是球形端盖造型与塑料模具设计。该设计结合大学三年来所学习的专业知识和CAD软件所设计出的一套塑料模。
本文首先简要的概述了塑料模在社会领域中的作用及其以后的发展方向,点明模具设计的重要意义。然后依据工件图进行工艺性分析,进而确定了设计方案,计算出模具工作部分的尺寸,设计出工作零部件;然后依据设计要求选择出各个标准零部件,然后设计出模具的总装配图。在设计中,最重要的就是设计方案的确定、坯料的计算和选取以及工作零部件的设计,这是设计的关键,这些设计的正确与否直接关系到成本的高低和设计模具能否正常工作;在设计的最后,总结了自己的心得和体会,并对我的指导老师表示感谢。
为了我的设计更加简明易懂,在设计中,我用了十几张零件图来说明我的设计意图,安插在设计任务书中。最后画出一幅球形端盖塑料模装配图和主要工作零部件零件图若干张。
通过本次毕业设计使我不仅掌握了塑料模具设计的一般流程,更学习到了好多课本上没有学习到的知识,使我受益匪浅。
关键词:模具设计与制造、CAD软件、工艺性分析。
                             
Head modelling and mold design of drain pipe                              
    Summary   
The speciality of study of our institute is the mold design and speciality of making, the graduation project this time is head modelling of the drain pipe and plastic mold design. It's time to design and combine the professional knowledge of study and a set of plastic moulds that CAD software designed over the past three years of university.
This text the brief plastic role in social field of mould of summary and developing direction afterwards at first, point out in the important meaning of mold design. Then carry on the craft to analyse according to the work piece picture , and then has confirmed the design plan , calculate out mould work some size , design the job spare part; Then choose each standard spare part according to the designing requirement , then design the total installation diagram of the mould . In the design, the important one is sureness of the design plan , calculation and choosing and working the design of the spare part of the blank the most, this is the key to designing, whether these ones that are designed involve directly or not correctly whether the level of the cost and design mould could work normally; At the end that is designed , have summarized one's own gains and experience , and express thanks for my counselor.
More concisly and easy for my design understands , in the design, I state my design intention with a dozen parts picture, assign into design specifications . Draw a drain pipe and several plastic mould installation diagrams of very beginning and spare part pictures of the groundwork finally.
Make me not merely grasp the general procedure of plastic mold design through graduation project once, study to the knowledge not learning to get on many textbooks even more, benefit me a great deal.
Keyword:  Mold design and making , CAD software , craft analysis.

分析制件的工艺性和注塑成型工艺规程对模具设计的要求
塑件制品为球形端盖,球形端盖是通过中间的四方型芯以及周边的圆与机身连接,为了更好的保证球形端盖与机身的装配关系与要求,周围的圆装配公差为0.1其余部分偏差值可按Js15,要求表面光滑,无毛刺,工作环境为一般;
    从该塑料制件制品图形上可以看出,该制件的形状结构不太复杂,但对尺寸大小,精度以及表面质量要求较高;
 

球形端盖造型与模具设计(含cad零件图和装配图)
球形端盖造型与模具设计(含cad零件图和装配图)
球形端盖造型与模具设计(含cad零件图和装配图)
球形端盖造型与模具设计(含cad零件图和装配图)


目 录
绪论------------------------------------------------------1
1 塑件工艺性分析----------------------------------------3
1.1  设计前的准备工作---------------------------------3
1.1.1明确设计任务和准备必要的技术资料-------------------------3
1.1.2分析研究原始材料的工艺特性和成型性能---------------------3
1.1.3分析制件的工艺性和注塑成型工艺规程对模具设计的要求-------4
1.2 计算塑件的体积和质量-------------------------------6
1.3.塑件注塑工艺参数的确定-----------------------------7
2.注塑模的结构设计-------------------------------------8
2.1.分型面的选择---------------------------------------8
2.2浇注系统的设计--------------------------------------8
2.2.1主流道设计-----------------------------------------------8
2.2.2主流道衬套的选取-----------------------------------------9
2.2.3分流道设计-----------------------------------------------9
2.2.4排气结构的设计------------------------------------------10
2.3.抽芯机构的设计-------------------------------------10
2.4.脱模机构的设计-------------------------------------11
2.5.成型零件的结构尺寸---------------------------------12
2.5.1凹模的结构设计-------------------------------------------12
2.5.2凸模的结构-----------------------------------------------12
3.模具设计的有关计算----------------------------------13
3.1.型腔与型芯工作尺寸的计----------------------------13
3.2.型腔侧壁厚度和底板厚度的计算----------------------14
3.2.1查相关手册----------------------------------------------14
3.2.2型腔侧壁厚度--------------------------------------------14
4.模具加热与冷却系统的计算---------------------------15
4.1计算热流量----------------------------------------15
4.2冷却水的体积流量V----------------------------15
 5.其它零件的设计及模具的闭合高度-------------------17
   5.1支承和固定零件的设计-------------------------------17
5.2.模具闭合高度的确定--------------------------------17
6.注塑机有关参数的校核---------------------------------18
7 其它设计说明------------------------------------------19
8 模具的装配-------------------------------------------20
9试模过程中出现的问题及解决办法------------------21
结论-----------------------------------------------------22
致谢-----------------------------------------------------23
参考文献-------------------------------------------------24

插图清单
【1】  图一  制品的形状………………………………………………………5
【2】  图二  分型面的选择……………………………………………………8
【3】  图三  主流套衬套……………………………………………………9
【4】 图四 抽芯机构  ……………………………………………… 11
【5】  图五 冷却水道……………………………………………………… 16
【6】 图六 螺钉……………………………………………… 17

附表清单
【1】    表一:型腔和型心工作尺寸的计算………………………………………  13
【2】  表二:   冷却水道的选取:(由计算选取)………………………………  16
【3】  表三:试模过程中出现的问题及解决办法 ……………………………  21

推荐资料